Industrial Cameras FAQ
- What is Bayer filter? （No293）
- The lower part of an image is occasionally replaced to another frame image. Please show how to prevent this issue. （No294）
- How can I convert a Raw image sent from camera to BGR or BGRA format image?（No1540）
- TeliGevViewer detects BG series camera, but captures no images.（No328）
- Color image converted from camera raw image shows inappropriate color. （No1519）
- Cannot get image even though succeeded in opening USB3.0 (BU / DU series) camera. （No1556）
- Want to know how to grab the image.（No1531）
- Time out error occurs when NI Measurement & Automation Explorer(MAX) application tried to grab an image whose data size exceeds 5M bytes. （No1561）
- How can I save an image sent from the camera to a file?（No1541）
- Where is library manual of TeliCamSDK? The start-up guide of TeliCamSDK says 'The specification of each function required for programming for using a camera is indicated in another document called "TeliCamSDK Library Manual".（No1532）
- A log message that an exception occurred due to GenICamLogConfig environment variable is missing is shown in Visual Studio log window on debugging a TeliCamSDK application. This exception have no harm in actual, and I can do debugging application without any problems, but please show me how to eliminate this exception.（No255）
- In case of pulse width mode, is there any up-limitation of exposure time? [camera] （No292）
- Please show how to convert the image obtained from camera to the image format that OpenCV library can processed.（No249）
- Is the Camera Description File (XML file) instruction manual available? （No1528）
- Does sensitivity rise at the binning function？ [CameraLink camera]（No302）
- How can I get firmware version of USB3.0 camera (BU / DU series)?（No1555）
- Grabbing an image with a size exceeding 5 Mbytes by NI MAX (Measurement & Automation Explorer) results in timeout.(Uses Fresco Logic USB host controller)（No250）
- Too dark images are acquired under flashing light synchronizing with external trigger signal.（No1517）
- What are IIDC and IIDC2? （No1546）
- It fails to start C# application which uses TeliCamSDK V2.0.1.1 on a PC that TeliCamSDK V1.0.7.2 or earlier is installed.（No227）
- What is the chunk function of cameras?（No1521）
- Camera outputs no signal to DIO(GPIO) pin. （No298）
- A camera is shown under multiple network adapters in IP Configuration Tool. How can I fix it?（No1527）
- The following compilar warning is reported in C# application. There was a mismatch between the processor architecture of the project being built "MSIL" and the processor architecture of the reference（No230）
- Image acquisition stops in USB3 Vision(BU) camera.（No1550）
- TeliU3vViewer does not show a BU series camera. Device manager shows it as a properly working device. （No1483）
- What is unit of timestamp member of image information structure in USB3.0 cameras (BU /DU series) and GigE Vision cameras (BG series)?（No1516）
- Please show how to get PixelFormats (data format of pixels in camera output image) available in a camera in user application program.（No1500）
- GigE Vision camera (BG series) is not shown in IP Configuration Tool. （No1565）
- It fails to write PixelFormat value written in the camera instruction manual to a camera.（No1520）
- Can BG series be used for TeliGCAM? [GigE camera]（No320）
- There are no VB.NET sample codes in TeliCamSDK package. Where can I get VB.net sample codes?（No1543）
- When TeliCamAPI Strm_ReadCurrentImage () is executed, BUFFER_TOO_SMALL is returned. (When CameraStream.ReadCurrentImage () is executed, CamApiStatus.BufferTooSmall will be returned.（No1538）
- How long is the maximum string length of UserDefinedName in USB3.0 cameras (BU / DU series) and GigE Vision cameras (BG series)?（No1513）
- Is it possible to design an application which can run on a PC that GenICam GenAPI library is not installed? （No1534）
- Don't know the setup method of multicast on TeliGevViewer [GigE camera]（No324）
- How many GigE Vision cameras (BG series) can application program handle?（No1566）
- I cannot find GenICam installation executing file.（No1530）
- "Not Installed" is shown at Filter driver item of Adapter’s Information in IP Configuration Tool.（No305）
- What is Bus Synchronization mode of USB3.0 cameras (BU / DU series)? （No1557）
- BG205M camera has FrameBurst mode feature. Please show how to set FrameBurst mode to a camera using TeliCamSDK. （No1536）
- The transfer speed can only be selected at S400 if you run TeliDCAM on Windows7. [IEEE1394 camera]（No1465）
- Frame rate becomes low when acquiring BU / DU camera images with Windows 10 PC using Intel 7000 series Core i 7, i 5, i 3 CPU (Kaby Lake).（No1560）
- Why there are cameras whose values writable to PixelFormat register are different from the other same model cameras?（No1518）
- What is BERT function of USB3.0 cameras (BU / DU series)?（No1558）
- Do GigE Vision cameras (BG series) have "User output" feature available in USB3.0 camera (BU / DU series) GPIO output? （No1567）
- It takes not short time to convert camera raw image data to BGR or BGRA format image. Are there solutions for making conversion time shorter?（No1537）
- INVALID_STREAM_HANDLE is returned from TeliCamAPI camera streaming functions（No1539）
- TeliGCAM multiple connection can not be recognized on Windows XP? [GigE camera]（No309）
- Show me how to check TeliCamSDK version.（No1524）